Initial commit: TXW82x FPV v2.7.0.7-42229 SDK + project sources

sdk/include/lib/touch/cst226se.h

@@ -0,0 +1,14 @@
+#ifndef __CST226SE_H_
+#define __CST226SE_H_
+
+#include "basic_include.h"
+#include "hal/i2c.h"
+#include "app_iic/app_iic.h"
+#include "lib/touch/hyn_core.h"
+#include "lib/touch/touch_pad.h"
+
+void cst226se_init();
+void *cst226se_get_multipoint_xy();
+uint32_t cst226se_free_multipoint_xy(void *data);
+
+#endif

sdk/include/lib/touch/hyn_core.h

@@ -0,0 +1,105 @@
+#ifndef __HYN_CORE_H_
+#define __HYN_CORE_H_
+
+#include "basic_include.h"
+
+#define HYN_ENTER()                 os_printf("%s %d\n",__func__,__LINE__)
+#define HYN_ERROR(fmt, args...)     os_printf(KERN_ERR "[HYN][Error]%s:"fmt"\n",__func__,##args)
+#define HYN_INFO(fmt, args...)      os_printf(KERN_INFO "[HYN][Info]%s:"fmt"\n",__func__,##args)
+
+#define U8TO16(x1,x2) ((((x1)&0xFF)<<8)|((x2)&0xFF))
+#define U8TO32(x1,x2,x3,x4) ((((x1)&0xFF)<<24)|(((x2)&0xFF)<<16)|(((x3)&0xFF)<<8)|((x4)&0xFF))
+#define U16REV(x)  ((((x)<<8)&0xFF00)|(((x)>>8)&0x00FF))
+
+#undef DISABLE
+#undef ENABLE
+#define DISABLE (0)
+#define ENABLE  (1)
+
+enum report_typ{
+    REPORT_NONE = 0,
+    REPORT_POS = 0x01,
+    REPORT_KEY = 0x02,
+    REPORT_GES = 0x04,
+    REPORT_PROX = 0x08
+};
+
+enum work_mode{
+    NOMAL_MODE = 0,
+    GESTURE_MODE = 1,
+    LP_MODE = 2,
+    DEEPSLEEP = 3,
+    DIFF_MODE = 4,
+    RAWDATA_MODE = 5,
+    BASELINE_MODE = 6,
+    CALIBRATE_MODE = 7,
+    FAC_TEST_MODE = 8,
+    GLOVE_EXIT = 0x10,
+    GLOVE_ENTER = 0x11,
+    CHARGE_EXIT = 0x12,
+    CHARGE_ENTER = 0x13,
+    ENTER_BOOT_MODE = 0xCA,
+};
+
+#define MAX_POINTS_REPORT     (10)
+struct ts_frame {
+    uint8_t rep_num;
+    enum report_typ report_need;
+    uint8_t key_id;
+    uint8_t key_state;
+    struct {
+        uint8_t pos_id;
+        uint8_t event;
+        uint16_t pos_x;
+        uint16_t pos_y;
+        uint16_t pres_z;
+    }pos_info[MAX_POINTS_REPORT];
+};
+
+struct tp_info {
+    uint8_t  fw_sensor_txnum;
+    uint8_t  fw_sensor_rxnum;
+    uint8_t  fw_key_num;
+    uint8_t  reserve;
+    uint16_t fw_res_y;
+    uint16_t fw_res_x;
+    uint32_t fw_boot_time;
+    uint32_t fw_project_id;
+    uint32_t fw_chip_type;
+    uint32_t fw_ver;
+    uint32_t ic_fw_checksum;
+    uint32_t fw_module_id;
+};
+
+struct hyn_plat_data {
+    uint32_t x_resolution;
+	uint32_t y_resolution;
+    int swap_xy;
+	int reverse_x;
+	int reverse_y;
+};
+
+struct hyn_ts_data {
+    struct os_work work;
+    struct os_event event;
+    struct  os_msgqueue msgque;
+    int app_iic_num;
+    int gpio_irq;
+    uint8_t  iic_addr;
+    enum work_mode work_mode;
+    struct hyn_plat_data plat_data;
+    int boot_is_pass;
+    struct tp_info hw_info;
+    struct ts_frame rp_buf;
+    uint8_t gesture_id;
+    uint8_t *iic_trx_buff;
+};
+
+int hyn_wr_reg(struct hyn_ts_data *ts_data, uint32_t reg_addr, uint32_t reg_len, uint8_t *rbuf, uint32_t rlen);
+
+void hyn_irq_set(struct hyn_ts_data *ts_data, uint8_t value);
+void hyn_esdcheck_switch(struct hyn_ts_data *ts_data, uint8_t enable);
+
+uint32_t hyn_sum32(int val, uint32_t* buf,uint16_t len);
+
+#endif

sdk/include/lib/touch/touch_pad.h

@@ -0,0 +1,32 @@
+#ifndef __TOUCH_PAD_H_
+#define __TOUCH_PAD_H_
+#include "basic_include.h"
+#ifdef PIN_FROM_PARAM
+#include "pin_param.h"
+#endif
+
+/* ------------ Selection of touch chips ------------ */
+
+#define CST226SE_TOUCH_PAD  1
+
+/* ------------------------------------------------- */
+
+#define MAX_POINT_NUM   5
+
+#undef PIN_TP_I2C_SCL
+#undef PIN_TP_I2C_SDA
+#undef PIN_TP_INT
+#undef PIN_TP_RST
+
+struct touch_multipoint_pos {
+    uint8_t point_num;
+    uint16_t pos_x[MAX_POINT_NUM];
+    uint16_t pos_y[MAX_POINT_NUM];
+};
+typedef struct touch_multipoint_pos touch_multipoint_pos_t;
+
+touch_multipoint_pos_t *touch_pad_get_multipoint_xy();
+uint32_t touch_pad_free_multipoint_xy(touch_multipoint_pos_t *data);
+void touch_pad_hareware_init();
+
+#endif