1039 lines
35 KiB
C
1039 lines
35 KiB
C
#include "app_config.h"
|
||
|
||
#ifdef CONFIG_BOARD_JL7018F_DEMO
|
||
|
||
#include "system/includes.h"
|
||
#include "media/includes.h"
|
||
#include "asm/sdmmc.h"
|
||
#include "asm/chargestore.h"
|
||
#include "asm/umidigi_chargestore.h"
|
||
#include "asm/charge.h"
|
||
#include "asm/pwm_led.h"
|
||
#include "tone_player.h"
|
||
#include "audio_config.h"
|
||
#include "gSensor/gSensor_manage.h"
|
||
#include "key_event_deal.h"
|
||
#include "asm/lp_touch_key_api.h"
|
||
#include "user_cfg.h"
|
||
#include "norflash_sfc.h"
|
||
#include "asm/power/power_port.h"
|
||
#include "app_umidigi_chargestore.h"
|
||
#include "app_main.h"
|
||
#include "audio_link.h"
|
||
#if TCFG_AUDIO_ANC_ENABLE
|
||
#include "audio_anc.h"
|
||
#endif/*TCFG_AUDIO_ANC_ENABLE*/
|
||
|
||
#define LOG_TAG_CONST BOARD
|
||
#define LOG_TAG "[BOARD]"
|
||
#define LOG_ERROR_ENABLE
|
||
#define LOG_DEBUG_ENABLE
|
||
#define LOG_INFO_ENABLE
|
||
/* #define LOG_DUMP_ENABLE */
|
||
#define LOG_CLI_ENABLE
|
||
#include "debug.h"
|
||
|
||
void board_power_init(void);
|
||
|
||
/*各个状态下默认的闪灯方式和提示音设置，如果USER_CFG中设置了USE_CONFIG_STATUS_SETTING为1，则会从配置文件读取对应的配置来填充改结构体*/
|
||
STATUS_CONFIG status_config = {
|
||
//灯状态设置
|
||
.led = {
|
||
.charge_start = PWM_LED1_ON,
|
||
.charge_full = PWM_LED0_ON,
|
||
.power_on = PWM_LED0_ON,
|
||
.power_off = PWM_LED1_FLASH_THREE,
|
||
.lowpower = PWM_LED1_SLOW_FLASH,
|
||
.max_vol = PWM_LED_NULL,
|
||
.phone_in = PWM_LED_NULL,
|
||
.phone_out = PWM_LED_NULL,
|
||
.phone_activ = PWM_LED_NULL,
|
||
.bt_init_ok = PWM_LED0_LED1_SLOW_FLASH,
|
||
.bt_connect_ok = PWM_LED0_ONE_FLASH_5S,
|
||
.bt_disconnect = PWM_LED0_LED1_FAST_FLASH,
|
||
.tws_connect_ok = PWM_LED0_LED1_FAST_FLASH,
|
||
.tws_disconnect = PWM_LED0_LED1_SLOW_FLASH,
|
||
},
|
||
//提示音设置
|
||
.tone = {
|
||
.charge_start = IDEX_TONE_NONE,
|
||
.charge_full = IDEX_TONE_NONE,
|
||
.power_on = IDEX_TONE_POWER_ON,
|
||
.power_off = IDEX_TONE_POWER_OFF,
|
||
.lowpower = IDEX_TONE_LOW_POWER,
|
||
.max_vol = IDEX_TONE_MAX_VOL,
|
||
.phone_in = IDEX_TONE_NONE,
|
||
.phone_out = IDEX_TONE_NONE,
|
||
.phone_activ = IDEX_TONE_NONE,
|
||
.bt_init_ok = IDEX_TONE_BT_MODE,
|
||
.bt_connect_ok = IDEX_TONE_BT_CONN,
|
||
.bt_disconnect = IDEX_TONE_BT_DISCONN,
|
||
.tws_connect_ok = IDEX_TONE_TWS_CONN,
|
||
.tws_disconnect = IDEX_TONE_TWS_DISCONN,
|
||
}
|
||
};
|
||
|
||
#define __this (&status_config)
|
||
|
||
/************************** KEY MSG****************************/
|
||
/*各个按键的消息设置，如果USER_CFG中设置了USE_CONFIG_KEY_SETTING为1，则会从配置文件读取对应的配置来填充改结构体*/
|
||
u8 key_table[KEY_NUM_MAX][KEY_EVENT_MAX] = {
|
||
// SHORT LONG HOLD UP DOUBLE TRIPLE
|
||
{KEY_MUSIC_PP, KEY_POWEROFF, KEY_POWEROFF_HOLD, KEY_NULL, KEY_NULL, KEY_NULL}, //KEY_0
|
||
{KEY_ANC_SWITCH, KEY_NULL, KEY_NULL, KEY_NULL, KEY_NULL, KEY_NULL}, //KEY_1
|
||
{KEY_MUSIC_PREV, KEY_VOL_UP, KEY_VOL_UP, KEY_NULL, KEY_NULL, KEY_NULL}, //KEY_2
|
||
{KEY_MUSIC_NEXT, KEY_VOL_DOWN, KEY_VOL_DOWN, KEY_NULL, KEY_NULL, KEY_NULL}, //KEY_3
|
||
{KEY_CALL_LAST_NO, KEY_NULL, KEY_NULL, KEY_NULL, KEY_NULL, KEY_NULL}, //KEY_4
|
||
};
|
||
|
||
|
||
// *INDENT-OFF*
|
||
/************************** UART config****************************/
|
||
#if TCFG_UART0_ENABLE
|
||
UART0_PLATFORM_DATA_BEGIN(uart0_data)
|
||
.tx_pin = TCFG_UART0_TX_PORT, //串口打印TX引脚选择
|
||
.rx_pin = TCFG_UART0_RX_PORT, //串口打印RX引脚选择
|
||
.baudrate = TCFG_UART0_BAUDRATE, //串口波特率
|
||
|
||
.flags = UART_DEBUG, //串口用来打印需要把改参数设置为UART_DEBUG
|
||
UART0_PLATFORM_DATA_END()
|
||
#endif //TCFG_UART0_ENABLE
|
||
|
||
/************************** CHARGE config****************************/
|
||
#if TCFG_CHARGE_ENABLE
|
||
CHARGE_PLATFORM_DATA_BEGIN(charge_data)
|
||
.charge_en = TCFG_CHARGE_ENABLE, //内置充电使能
|
||
.charge_poweron_en = TCFG_CHARGE_POWERON_ENABLE, //是否支持充电开机
|
||
.charge_full_V = TCFG_CHARGE_FULL_V, //充电截止电压
|
||
.charge_full_mA = TCFG_CHARGE_FULL_MA, //充电截止电流
|
||
.charge_mA = TCFG_CHARGE_MA, //恒流充电电流
|
||
.charge_trickle_mA = TCFG_CHARGE_TRICKLE_MA, //涓流充电电流
|
||
/*ldo5v拔出过滤值，过滤时间 = (filter*2 + 20)ms,ldoin<0.6V且时间大于过滤时间才认为拔出
|
||
对于充满直接从5V掉到0V的充电仓，该值必须设置成0，对于充满由5V先掉到0V之后再升压到xV的
|
||
充电仓，需要根据实际情况设置该值大小*/
|
||
.ldo5v_off_filter = 100,
|
||
.ldo5v_on_filter = 50,
|
||
.ldo5v_keep_filter = 220,
|
||
.ldo5v_pulldown_lvl = CHARGE_PULLDOWN_200K, //下拉电阻档位选择
|
||
.ldo5v_pulldown_keep = 0,
|
||
//1、对于自动升压充电舱,若充电舱需要更大的负载才能检测到插入时，请将该变量置1,并且根据需求配置下拉电阻档位
|
||
//2、对于按键升压,并且是通过上拉电阻去提供维持电压的舱,请将该变量设置1,并且根据舱的上拉配置下拉需要的电阻挡位
|
||
//3、对于常5V的舱,可将改变量设为0,省功耗
|
||
//4、为LDOIN防止被误触发唤醒,可设置为200k下拉
|
||
.ldo5v_pulldown_en = 1,
|
||
CHARGE_PLATFORM_DATA_END()
|
||
#endif//TCFG_CHARGE_ENABLE
|
||
|
||
/************************** chargestore config****************************/
|
||
#if TCFG_CHARGESTORE_ENABLE || TCFG_TEST_BOX_ENABLE || TCFG_ANC_BOX_ENABLE
|
||
CHARGESTORE_PLATFORM_DATA_BEGIN(chargestore_data)
|
||
.io_port = TCFG_CHARGESTORE_PORT,
|
||
CHARGESTORE_PLATFORM_DATA_END()
|
||
#endif
|
||
|
||
/************************** DAC ****************************/
|
||
#if TCFG_AUDIO_DAC_ENABLE
|
||
struct dac_platform_data dac_data = {
|
||
.mode = TCFG_AUDIO_DAC_MODE, //dac输出模式
|
||
.ldo_id = TCFG_AUDIO_DAC_LDO_SEL, //保留位
|
||
.pa_mute_port = TCFG_AUDIO_DAC_PA_PORT, //暂时无作用
|
||
.vcmo_en = 0, //是否打开VCOMO
|
||
.pa_mute_value = 1, //暂时无作用
|
||
.output = TCFG_AUDIO_DAC_CONNECT_MODE, //DAC输出配置，和具体硬件连接有关，需根据硬件来设置
|
||
.lpf_isel = 0xf,
|
||
.sys_vol_type = SYS_VOL_TYPE, //系统音量选择：模拟音量/数字音量，调节时调节对应的音量
|
||
.max_ana_vol = MAX_ANA_VOL, //模拟音量最大等级
|
||
.max_dig_vol = MAX_DIG_VOL, //数字音量最大等级
|
||
/* .dig_vol_tab = (s16 *)dig_vol_table, //数字音量表 */
|
||
.vcm_cap_en = 1, //配1代表走外部通路,vcm上有电容时,可以提升电路抑制电源噪声能力，提高ADC的性能，配0相当于vcm上无电容，抑制电源噪声能力下降,ADC性能下降
|
||
#if (SYS_VOL_TYPE == VOL_TYPE_AD)
|
||
.digital_gain_limit = 16384,
|
||
#endif // #if (SYS_VOL_TYPE == VOL_TYPE_AD)
|
||
|
||
.power_on_mode = 0,
|
||
};
|
||
#endif
|
||
|
||
/************************** ADC ****************************/
|
||
#if TCFG_AUDIO_ADC_ENABLE
|
||
#ifndef TCFG_AUDIO_MIC0_BIAS_EN
|
||
#define TCFG_AUDIO_MIC0_BIAS_EN 0
|
||
#endif/*TCFG_AUDIO_MIC0_BIAS_EN*/
|
||
#ifndef TCFG_AUDIO_MIC1_BIAS_EN
|
||
#define TCFG_AUDIO_MIC1_BIAS_EN 0
|
||
#endif/*TCFG_AUDIO_MIC1_BIAS_EN*/
|
||
#ifndef TCFG_AUDIO_MIC2_BIAS_EN
|
||
#define TCFG_AUDIO_MIC2_BIAS_EN 0
|
||
#endif/*TCFG_AUDIO_MIC2_BIAS_EN*/
|
||
#ifndef TCFG_AUDIO_MIC3_BIAS_EN
|
||
#define TCFG_AUDIO_MIC3_BIAS_EN 0
|
||
#endif/*TCFG_AUDIO_MIC3_BIAS_EN*/
|
||
#ifndef TCFG_AUDIO_MIC_LDO_EN
|
||
#define TCFG_AUDIO_MIC_LDO_EN 0
|
||
#endif/*TCFG_AUDIO_MIC_LDO_EN*/
|
||
|
||
struct adc_platform_data adc_data = {
|
||
|
||
/*MIC LDO电流档位设置：
|
||
0:0.625ua 1:1.25ua 2:1.875ua 3:2.5ua*/
|
||
.mic_ldo_isel = TCFG_AUDIO_ADC_LD0_SEL,
|
||
|
||
/*mic_mode 工作模式定义
|
||
#define AUDIO_MIC_CAP_MODE 0 //单端隔直电容模式
|
||
#define AUDIO_MIC_CAP_DIFF_MODE 1 //差分隔直电容模式
|
||
#define AUDIO_MIC_CAPLESS_MODE 2 //单端省电容模式
|
||
*/
|
||
.mic_mode = TCFG_AUDIO_MIC_MODE,
|
||
.mic1_mode = TCFG_AUDIO_MIC1_MODE,
|
||
.mic2_mode = TCFG_AUDIO_MIC2_MODE,
|
||
.mic3_mode = TCFG_AUDIO_MIC3_MODE,
|
||
|
||
.mic_bias_inside = TCFG_AUDIO_MIC0_BIAS_EN,
|
||
.mic1_bias_inside = TCFG_AUDIO_MIC1_BIAS_EN,
|
||
.mic2_bias_inside = TCFG_AUDIO_MIC2_BIAS_EN,
|
||
.mic3_bias_inside = TCFG_AUDIO_MIC3_BIAS_EN,
|
||
|
||
/*MICLDO供电输出到PAD(PA0)控制使能*/
|
||
.mic_ldo_pwr = TCFG_AUDIO_MIC_LDO_EN, // MIC LDO 输出到 PA0
|
||
|
||
/*MIC免电容方案需要设置，影响MIC的偏置电压
|
||
0b0001~0b1001 : 0.5k ~ 4.5k step = 0.5k
|
||
0b1010~0b1111 : 5k ~ 10k step = 1k */
|
||
.mic_bias_res = 4,
|
||
.mic1_bias_res = 4,
|
||
.mic2_bias_res = 4,
|
||
.mic3_bias_res = 4,
|
||
/*MIC LDO电压档位设置,也会影响MIC的偏置电压
|
||
0:1.3v 1:1.4v 2:1.5v 3:2.0v
|
||
4:2.2v 5:2.4v 6:2.6v 7:2.8v */
|
||
.mic_ldo_vsel = 5,
|
||
//mic的去直流dcc寄存器配置值,可配0到15,数值越大,其高通转折点越低
|
||
.mic_dcc = 8,
|
||
};
|
||
#endif
|
||
|
||
#if TCFG_SMART_VOICE_ENABLE
|
||
const struct vad_mic_platform_data vad_mic_data = {
|
||
.mic_data = { //
|
||
.mic_mode = TCFG_AUDIO_MIC_MODE,
|
||
.mic_ldo_isel = 2,
|
||
.mic_ldo_vsel = 5,
|
||
.mic_ldo2PAD_en = 1,
|
||
.mic_bias_en = 0,
|
||
.mic_bias_res = 0,
|
||
.mic_bias_inside = TCFG_AUDIO_MIC0_BIAS_EN,
|
||
/* ADC偏置电阻配置*/
|
||
.adc_rbs = 3,
|
||
/* ADC输入电阻配置*/
|
||
.adc_rin = 3,
|
||
/*.adc_test = 1,*/
|
||
},
|
||
.power_data = {
|
||
/*VADLDO电压档位：0~7*/
|
||
.ldo_vs = 3,
|
||
/*VADLDO误差运放电流档位：0~3*/
|
||
#if TCFG_VAD_LOWPOWER_CLOCK == VAD_CLOCK_USE_PMU_STD12M
|
||
.ldo_is = 1,
|
||
#else
|
||
.ldo_is = 2,
|
||
#endif
|
||
.clock = TCFG_VAD_LOWPOWER_CLOCK, /*VAD时钟选项*/
|
||
.acm_select = 8,
|
||
},
|
||
};
|
||
#endif
|
||
/* struct audio_pf_data audio_pf_d = { */
|
||
/* #if TCFG_AUDIO_DAC_ENABLE */
|
||
/* .adc_pf_data = &adc_data, */
|
||
/* #endif */
|
||
|
||
/* #if TCFG_AUDIO_ADC_ENABLE */
|
||
/* .dac_pf_data = &dac_data, */
|
||
/* #endif */
|
||
/* }; */
|
||
|
||
/* struct audio_platform_data audio_data = { */
|
||
/* .private_data = (void *) &audio_pf_d, */
|
||
/* }; */
|
||
|
||
|
||
/************************** IO KEY ****************************/
|
||
#if TCFG_IOKEY_ENABLE
|
||
const struct iokey_port iokey_list[] = {
|
||
|
||
{
|
||
.connect_way = TCFG_IOKEY_POWER_CONNECT_WAY, //IO按键的连接方式
|
||
.key_type.one_io.port = TCFG_IOKEY_POWER_ONE_PORT, //IO按键对应的引脚
|
||
.key_value = 0, //按键值
|
||
},
|
||
#if CLIENT_BOARD == HEAD_FB || \
|
||
CLIENT_BOARD == HEAD_HYBRID
|
||
{
|
||
.connect_way = TCFG_IOKEY_MFB_CONNECT_WAY, //IO按键的连接方式
|
||
.key_type.one_io.port = TCFG_IOKEY_MFB_ONE_PORT, //IO按键对应的引脚
|
||
.key_value = 1, //按键值
|
||
},
|
||
{
|
||
.connect_way = TCFG_IOKEY_PREV_CONNECT_WAY, //IO按键的连接方式
|
||
.key_type.one_io.port = TCFG_IOKEY_PREV_ONE_PORT, //IO按键对应的引脚
|
||
.key_value = 2, //按键值
|
||
},
|
||
{
|
||
.connect_way = TCFG_IOKEY_NEXT_CONNECT_WAY, //IO按键的连接方式
|
||
.key_type.one_io.port = TCFG_IOKEY_NEXT_ONE_PORT, //IO按键对应的引脚
|
||
.key_value = 3, //按键值
|
||
},
|
||
{
|
||
.connect_way = TCFG_IOKEY_CALL_CONNECT_WAY, //IO按键的连接方式
|
||
.key_type.one_io.port = TCFG_IOKEY_CALL_ONE_PORT, //IO按键对应的引脚
|
||
.key_value = 4, //按键值
|
||
},
|
||
#endif
|
||
};
|
||
const struct iokey_platform_data iokey_data = {
|
||
.enable = TCFG_IOKEY_ENABLE, //是否使能IO按键
|
||
.num = ARRAY_SIZE(iokey_list), //IO按键的个数
|
||
.port = iokey_list, //IO按键参数表
|
||
};
|
||
|
||
#if MULT_KEY_ENABLE
|
||
//组合按键消息映射表
|
||
//配置注意事项:单个按键按键值需要按照顺序编号,如power:0, prev:1, next:2
|
||
//bit_value = BIT(0) | BIT(1) 指按键值为0和按键值为1的两个按键被同时按下,
|
||
//remap_value = 3指当这两个按键被同时按下后重新映射的按键值;
|
||
const struct key_remap iokey_remap_table[] = {
|
||
{.bit_value = BIT(0) | BIT(1), .remap_value = 3},
|
||
{.bit_value = BIT(0) | BIT(2), .remap_value = 4},
|
||
{.bit_value = BIT(1) | BIT(2), .remap_value = 5},
|
||
};
|
||
|
||
const struct key_remap_data iokey_remap_data = {
|
||
.remap_num = ARRAY_SIZE(iokey_remap_table),
|
||
.table = iokey_remap_table,
|
||
};
|
||
#endif
|
||
|
||
#endif
|
||
/*********************** LP TOUCH KEY ****************************/
|
||
#if TCFG_LP_TOUCH_KEY_ENABLE
|
||
const struct lp_touch_key_platform_data lp_touch_key_config = {
|
||
/*触摸按键*/
|
||
.ch[0].enable = TCFG_LP_TOUCH_KEY0_EN,
|
||
.ch[0].wakeup_enable = TCFG_LP_TOUCH_KEY0_WAKEUP_EN,
|
||
.ch[0].port = IO_PORTB_00,
|
||
.ch[0].sensitivity = TCFG_LP_TOUCH_KEY0_SENSITIVITY,
|
||
.ch[0].key_value = 0,
|
||
|
||
.ch[1].enable = TCFG_LP_TOUCH_KEY1_EN,
|
||
.ch[1].wakeup_enable = TCFG_LP_TOUCH_KEY1_WAKEUP_EN,
|
||
.ch[1].port = IO_PORTB_01,
|
||
.ch[1].sensitivity = TCFG_LP_TOUCH_KEY1_SENSITIVITY,
|
||
.ch[1].key_value = 0,
|
||
|
||
.ch[2].enable = TCFG_LP_TOUCH_KEY2_EN,
|
||
.ch[2].wakeup_enable = TCFG_LP_TOUCH_KEY2_WAKEUP_EN,
|
||
.ch[2].port = IO_PORTB_02,
|
||
.ch[2].sensitivity = TCFG_LP_TOUCH_KEY2_SENSITIVITY,
|
||
.ch[2].key_value = 1,
|
||
|
||
.ch[3].enable = TCFG_LP_TOUCH_KEY3_EN,
|
||
.ch[3].wakeup_enable = TCFG_LP_TOUCH_KEY3_WAKEUP_EN,
|
||
.ch[3].port = IO_PORTB_04,
|
||
.ch[3].sensitivity = TCFG_LP_TOUCH_KEY3_SENSITIVITY,
|
||
.ch[3].key_value = 2,
|
||
|
||
.ch[4].enable = TCFG_LP_TOUCH_KEY4_EN,
|
||
.ch[4].wakeup_enable = TCFG_LP_TOUCH_KEY4_WAKEUP_EN,
|
||
.ch[4].port = IO_PORTB_05,
|
||
.ch[4].sensitivity = TCFG_LP_TOUCH_KEY4_SENSITIVITY,
|
||
.ch[4].key_value = 3,
|
||
|
||
//把触摸按键之间的滑动也当做按键处理，有上滑，下滑，左滑，右滑
|
||
.slide_mode_en = TCFG_LP_SLIDE_KEY_ENABLE,
|
||
.slide_mode_key_value = 3,
|
||
|
||
//入耳检测相关的配置
|
||
.eartch_en = TCFG_LP_EARTCH_KEY_ENABLE,
|
||
.eartch_ch = TCFG_LP_EARTCH_KEY_CH,
|
||
.eartch_ref_ch = TCFG_LP_EARTCH_KEY_REF_CH,
|
||
.eartch_soft_inear_val = TCFG_LP_EARTCH_SOFT_INEAR_VAL,
|
||
.eartch_soft_outear_val = TCFG_LP_EARTCH_SOFT_OUTEAR_VAL,
|
||
};
|
||
#endif /* #if TCFG_LP_TOUCH_KEY_ENABLE */
|
||
|
||
/************************** PLCNT TOUCH_KEY ****************************/
|
||
#if TCFG_TOUCH_KEY_ENABLE
|
||
const const struct touch_key_port touch_key_list[] = {
|
||
{
|
||
.press_delta = TCFG_TOUCH_KEY0_PRESS_DELTA,
|
||
.port = TCFG_TOUCH_KEY0_PORT,
|
||
.key_value = TCFG_TOUCH_KEY0_VALUE,
|
||
},
|
||
{
|
||
.press_delta = TCFG_TOUCH_KEY1_PRESS_DELTA,
|
||
.port = TCFG_TOUCH_KEY1_PORT,
|
||
.key_value = TCFG_TOUCH_KEY1_VALUE,
|
||
},
|
||
};
|
||
|
||
const struct touch_key_platform_data touch_key_data = {
|
||
.num = ARRAY_SIZE(touch_key_list),
|
||
.port_list = touch_key_list,
|
||
};
|
||
#endif /* #if TCFG_TOUCH_KEY_ENABLE */
|
||
|
||
/************************** AD KEY ****************************/
|
||
#if TCFG_ADKEY_ENABLE
|
||
const struct adkey_platform_data adkey_data = {
|
||
.enable = TCFG_ADKEY_ENABLE, //AD按键使能
|
||
.adkey_pin = TCFG_ADKEY_PORT, //AD按键对应引脚
|
||
.ad_channel = TCFG_ADKEY_AD_CHANNEL, //AD通道值
|
||
.extern_up_en = TCFG_ADKEY_EXTERN_UP_ENABLE, //是否使用外接上拉电阻
|
||
.ad_value = { //根据电阻算出来的电压值
|
||
TCFG_ADKEY_VOLTAGE0,
|
||
TCFG_ADKEY_VOLTAGE1,
|
||
TCFG_ADKEY_VOLTAGE2,
|
||
TCFG_ADKEY_VOLTAGE3,
|
||
TCFG_ADKEY_VOLTAGE4,
|
||
TCFG_ADKEY_VOLTAGE5,
|
||
TCFG_ADKEY_VOLTAGE6,
|
||
TCFG_ADKEY_VOLTAGE7,
|
||
TCFG_ADKEY_VOLTAGE8,
|
||
TCFG_ADKEY_VOLTAGE9,
|
||
},
|
||
.key_value = { //AD按键各个按键的键值
|
||
TCFG_ADKEY_VALUE0,
|
||
TCFG_ADKEY_VALUE1,
|
||
TCFG_ADKEY_VALUE2,
|
||
TCFG_ADKEY_VALUE3,
|
||
TCFG_ADKEY_VALUE4,
|
||
TCFG_ADKEY_VALUE5,
|
||
TCFG_ADKEY_VALUE6,
|
||
TCFG_ADKEY_VALUE7,
|
||
TCFG_ADKEY_VALUE8,
|
||
TCFG_ADKEY_VALUE9,
|
||
},
|
||
};
|
||
#endif
|
||
|
||
/************************** RDEC_KEY ****************************/
|
||
#if TCFG_RDEC_KEY_ENABLE
|
||
const struct rdec_device rdeckey_list[] = {
|
||
{
|
||
.index = RDEC0 ,
|
||
.sin_port0 = TCFG_RDEC0_ECODE1_PORT,
|
||
.sin_port1 = TCFG_RDEC0_ECODE2_PORT,
|
||
.key_value0 = TCFG_RDEC0_KEY0_VALUE | BIT(7),
|
||
.key_value1 = TCFG_RDEC0_KEY1_VALUE | BIT(7),
|
||
},
|
||
|
||
{
|
||
.index = RDEC1 ,
|
||
.sin_port0 = TCFG_RDEC1_ECODE1_PORT,
|
||
.sin_port1 = TCFG_RDEC1_ECODE2_PORT,
|
||
.key_value0 = TCFG_RDEC1_KEY0_VALUE | BIT(7),
|
||
.key_value1 = TCFG_RDEC1_KEY1_VALUE | BIT(7),
|
||
},
|
||
|
||
{
|
||
.index = RDEC2 ,
|
||
.sin_port0 = TCFG_RDEC2_ECODE1_PORT,
|
||
.sin_port1 = TCFG_RDEC2_ECODE2_PORT,
|
||
.key_value0 = TCFG_RDEC2_KEY0_VALUE | BIT(7),
|
||
.key_value1 = TCFG_RDEC2_KEY1_VALUE | BIT(7),
|
||
},
|
||
|
||
|
||
};
|
||
const struct rdec_platform_data rdec_key_data = {
|
||
.enable = 1, //TCFG_RDEC_KEY_ENABLE, //是否使能RDEC按键
|
||
.num = ARRAY_SIZE(rdeckey_list), //RDEC按键的个数
|
||
.rdec = rdeckey_list, //RDEC按键参数表
|
||
};
|
||
#endif
|
||
|
||
/************************** IIS config ****************************/
|
||
#if (TCFG_AUDIO_INPUT_IIS || TCFG_AUDIO_OUTPUT_IIS)
|
||
ALINK_PARM alink0_platform_data = {
|
||
.module = ALINK0,
|
||
.mclk_io = TCFG_IIS_MCLK_IO,
|
||
.sclk_io = TCFG_SCLK_IO,
|
||
.lrclk_io = TCFG_LRCLK_IO,
|
||
.ch_cfg[0].data_io = TCFG_DATA0_IO,
|
||
.ch_cfg[1].data_io = TCFG_DATA1_IO,
|
||
.ch_cfg[2].data_io = TCFG_DATA2_IO,
|
||
.ch_cfg[3].data_io = TCFG_DATA3_IO,
|
||
.mode = ALINK_MD_IIS,
|
||
#if TCFG_IIS_MODE
|
||
.role = ALINK_ROLE_SLAVE,
|
||
#else
|
||
.role = ALINK_ROLE_MASTER,
|
||
#endif /*TCFG_IIS_MODE*/
|
||
.clk_mode = ALINK_CLK_FALL_UPDATE_RAISE_SAMPLE,
|
||
.bitwide = ALINK_LEN_16BIT,
|
||
.sclk_per_frame = ALINK_FRAME_32SCLK,
|
||
.dma_len = 4 * 1024,
|
||
.sample_rate = TCFG_IIS_SR,
|
||
.buf_mode = ALINK_BUF_CIRCLE,
|
||
/*.iperiod = 64, //配置该项可以控制输入的延时*/
|
||
};
|
||
#endif
|
||
|
||
/************************** PWM_LED ****************************/
|
||
#if TCFG_PWMLED_ENABLE
|
||
LED_PLATFORM_DATA_BEGIN(pwm_led_data)
|
||
.io_mode = TCFG_PWMLED_IOMODE, //推灯模式设置:支持单个IO推两个灯和两个IO推两个灯
|
||
.io_cfg.one_io.pin = TCFG_PWMLED_PIN, //单个IO推两个灯的IO口配置
|
||
LED_PLATFORM_DATA_END()
|
||
#endif
|
||
|
||
#if 0
|
||
const struct soft_iic_config soft_iic_cfg[] = {
|
||
//iic0 data
|
||
{
|
||
.scl = TCFG_SW_I2C0_CLK_PORT, //IIC CLK脚
|
||
.sda = TCFG_SW_I2C0_DAT_PORT, //IIC DAT脚
|
||
.delay = TCFG_SW_I2C0_DELAY_CNT, //软件IIC延时参数，影响通讯时钟频率
|
||
.io_pu = 1, //是否打开上拉电阻，如果外部电路没有焊接上拉电阻需要置1
|
||
},
|
||
#if 0
|
||
//iic1 data
|
||
{
|
||
.scl = IO_PORTA_05,
|
||
.sda = IO_PORTA_06,
|
||
.delay = 50,
|
||
.io_pu = 1,
|
||
},
|
||
#endif
|
||
};
|
||
|
||
|
||
const struct hw_iic_config hw_iic_cfg[] = {
|
||
//iic0 data
|
||
{
|
||
/*硬件IIC端口下选择
|
||
SCL SDA
|
||
{IO_PORT_DP, IO_PORT_DM}, //group a
|
||
{IO_PORTC_04, IO_PORTC_05}, //group b
|
||
{IO_PORTC_02, IO_PORTC_03}, //group c
|
||
{IO_PORTA_05, IO_PORTA_06}, //group d
|
||
*/
|
||
.port = TCFG_HW_I2C0_PORTS,
|
||
.baudrate = TCFG_HW_I2C0_CLK, //IIC通讯波特率
|
||
.hdrive = 0, //是否打开IO口强驱
|
||
.io_filter = 1, //是否打开滤波器（去纹波）
|
||
.io_pu = 1, //是否打开上拉电阻，如果外部电路没有焊接上拉电阻需要置1
|
||
},
|
||
};
|
||
#endif
|
||
|
||
#if TCFG_SD0_ENABLE
|
||
SD0_PLATFORM_DATA_BEGIN(sd0_data)
|
||
.port = {
|
||
TCFG_SD0_PORT_CMD,
|
||
TCFG_SD0_PORT_CLK,
|
||
TCFG_SD0_PORT_DA0,
|
||
TCFG_SD0_PORT_DA1,
|
||
TCFG_SD0_PORT_DA2,
|
||
TCFG_SD0_PORT_DA3,
|
||
},
|
||
.data_width = TCFG_SD0_DAT_MODE,
|
||
.speed = TCFG_SD0_CLK,
|
||
.detect_mode = TCFG_SD0_DET_MODE,
|
||
.priority = 3,
|
||
|
||
#if (TCFG_SD0_DET_MODE == SD_IO_DECT)
|
||
.detect_io = TCFG_SD0_DET_IO,
|
||
.detect_io_level = TCFG_SD0_DET_IO_LEVEL,
|
||
.detect_func = sdmmc_0_io_detect,
|
||
.power = sd_set_power,
|
||
/* .power = NULL, */
|
||
#elif (TCFG_SD0_DET_MODE == SD_CLK_DECT)
|
||
.detect_io_level = TCFG_SD0_DET_IO_LEVEL,
|
||
.detect_func = sdmmc_0_clk_detect,
|
||
.power = sd_set_power,
|
||
/* .power = NULL, */
|
||
#else
|
||
.detect_func = sdmmc_cmd_detect,
|
||
.power = NULL,
|
||
#endif
|
||
|
||
SD0_PLATFORM_DATA_END()
|
||
#endif /* #if TCFG_SD0_ENABLE */
|
||
|
||
REGISTER_DEVICES(device_table) = {
|
||
/* { "audio", &audio_dev_ops, (void *) &audio_data }, */
|
||
|
||
#if TCFG_CHARGE_ENABLE
|
||
{ "charge", &charge_dev_ops, (void *)&charge_data },
|
||
#endif
|
||
#if TCFG_SD0_ENABLE
|
||
{ "sd0", &sd_dev_ops, (void *) &sd0_data},
|
||
#endif
|
||
};
|
||
|
||
/************************** power_param ****************************/
|
||
const struct low_power_param power_param = {
|
||
.config = TCFG_LOWPOWER_LOWPOWER_SEL, //低功耗使能，蓝牙&&系统空闲可进入低功耗
|
||
.btosc_hz = TCFG_CLOCK_OSC_HZ, //蓝牙晶振频率
|
||
.delay_us = TCFG_CLOCK_SYS_HZ / 1000000L, //提供给低功耗模块的延时(不需要需修改)
|
||
.vddiom_lev = TCFG_LOWPOWER_VDDIOM_LEVEL, //vddiom等级
|
||
.osc_type = TCFG_LOWPOWER_OSC_TYPE, //低功耗晶振类型，btosc/lrc
|
||
#if (TCFG_LOWPOWER_RAM_SIZE)
|
||
.mem_init_con = MEM_PWR_RAM_SET(TCFG_LOWPOWER_RAM_SIZE),
|
||
#else
|
||
.mem_init_con = 0,
|
||
#endif
|
||
#if (TCFG_LP_TOUCH_KEY_ENABLE && \
|
||
(TCFG_LP_TOUCH_KEY0_WAKEUP_EN || \
|
||
TCFG_LP_TOUCH_KEY1_WAKEUP_EN || \
|
||
TCFG_LP_TOUCH_KEY2_WAKEUP_EN || \
|
||
TCFG_LP_TOUCH_KEY3_WAKEUP_EN || \
|
||
TCFG_LP_TOUCH_KEY4_WAKEUP_EN ))
|
||
.lpctmu_en = 1,
|
||
#else
|
||
.lpctmu_en = 0,
|
||
#endif
|
||
};
|
||
|
||
/************************** wk_param ****************************/
|
||
struct port_wakeup port0 = {
|
||
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.filter = PORT_FLT_8ms,
|
||
.iomap = TCFG_IOKEY_POWER_ONE_PORT, //唤醒口选择
|
||
};
|
||
|
||
#if CLIENT_BOARD == HEAD_FB || \
|
||
CLIENT_BOARD == HEAD_HYBRID
|
||
struct port_wakeup port2 = {
|
||
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.filter = PORT_FLT_8ms,
|
||
.iomap = TCFG_IOKEY_MFB_ONE_PORT, //唤醒口选择
|
||
};
|
||
struct port_wakeup port3 = {
|
||
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.filter = PORT_FLT_8ms,
|
||
.iomap = TCFG_IOKEY_PREV_ONE_PORT, //唤醒口选择
|
||
};
|
||
struct port_wakeup port4 = {
|
||
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.filter = PORT_FLT_8ms,
|
||
.iomap = TCFG_IOKEY_NEXT_ONE_PORT, //唤醒口选择
|
||
};
|
||
struct port_wakeup port5 = {
|
||
.pullup_down_enable = ENABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.filter = PORT_FLT_8ms,
|
||
.iomap = TCFG_IOKEY_CALL_ONE_PORT, //唤醒口选择
|
||
};
|
||
#endif
|
||
|
||
#if (TCFG_TEST_BOX_ENABLE || TCFG_CHARGESTORE_ENABLE || TCFG_ANC_BOX_ENABLE || TCFG_UMIDIGI_BOX_ENABLE)
|
||
struct port_wakeup port1 = {
|
||
.pullup_down_enable = DISABLE, //配置I/O 内部上下拉是否使能
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿
|
||
.filter = PORT_FLT_1ms,
|
||
.iomap = TCFG_CHARGESTORE_PORT, //唤醒口选择
|
||
};
|
||
#endif
|
||
|
||
#if TCFG_CHARGE_ENABLE
|
||
struct port_wakeup charge_port = {
|
||
.edge = RISING_EDGE, //唤醒方式选择,可选：上升沿\下降沿\双边沿
|
||
.filter = PORT_FLT_16ms,
|
||
.iomap = IO_CHGFL_DET, //唤醒口选择
|
||
};
|
||
|
||
struct port_wakeup vbat_port = {
|
||
.edge = BOTH_EDGE, //唤醒方式选择,可选：上升沿\下降沿\双边沿
|
||
.filter = PORT_FLT_16ms,
|
||
.iomap = IO_VBTCH_DET, //唤醒口选择
|
||
};
|
||
|
||
struct port_wakeup ldoin_port = {
|
||
.edge = BOTH_EDGE, //唤醒方式选择,可选：上升沿\下降沿\双边沿
|
||
.filter = PORT_FLT_16ms,
|
||
.iomap = IO_LDOIN_DET, //唤醒口选择
|
||
};
|
||
|
||
#if TCFG_EXTERN_CHARGE_ENABLE
|
||
struct port_wakeup ex_charge_port = {
|
||
.edge = FALLING_EDGE, //唤醒方式选择,可选：上升沿\下降沿\双边沿
|
||
.filter = PORT_FLT_16ms,
|
||
.iomap = TCFG_EXTERN_CHARGE_PORT, //唤醒口选择
|
||
};
|
||
#endif
|
||
|
||
#endif
|
||
|
||
const struct wakeup_param wk_param = {
|
||
#if (!(TCFG_LP_TOUCH_KEY_ENABLE && TCFG_LP_TOUCH_KEY1_EN))
|
||
.port[1] = &port0,
|
||
#if CLIENT_BOARD == HEAD_FB || \
|
||
CLIENT_BOARD == HEAD_HYBRID
|
||
//头戴式全部按键唤醒增加灵敏度,但会增加少许可忽略功耗。该处定义只会唤醒，按键开机需要在get_power_on_status增加判断
|
||
.port[3] = &port2,
|
||
.port[4] = &port3,
|
||
.port[5] = &port4,
|
||
.port[6] = &port5,
|
||
#endif
|
||
|
||
#endif
|
||
#if (TCFG_TEST_BOX_ENABLE || TCFG_CHARGESTORE_ENABLE || TCFG_ANC_BOX_ENABLE || TCFG_UMIDIGI_BOX_ENABLE)
|
||
/* TCFG_CHARGESTORE_PORT */
|
||
.port[2] = &port1,
|
||
#endif
|
||
#if TCFG_CHARGE_ENABLE
|
||
#if TCFG_EXTERN_CHARGE_ENABLE
|
||
/* TCFG_EXTERN_CHARGE_PORT */
|
||
.port[7] = &ex_charge_port,
|
||
#endif
|
||
.aport[0] = &charge_port,
|
||
.aport[1] = &vbat_port,
|
||
.aport[2] = &ldoin_port,
|
||
#endif
|
||
};
|
||
|
||
void gSensor_wkupup_disable(void)
|
||
{
|
||
log_info("gSensor wkup disable\n");
|
||
power_wakeup_index_enable(1, 0);
|
||
}
|
||
|
||
void gSensor_wkupup_enable(void)
|
||
{
|
||
log_info("gSensor wkup enable\n");
|
||
power_wakeup_index_enable(1, 1);
|
||
}
|
||
|
||
void debug_uart_init(const struct uart_platform_data *data)
|
||
{
|
||
#if TCFG_UART0_ENABLE
|
||
if (data) {
|
||
uart_init(data);
|
||
} else {
|
||
uart_init(&uart0_data);
|
||
}
|
||
#endif
|
||
}
|
||
|
||
|
||
STATUS *get_led_config(void)
|
||
{
|
||
return &(__this->led);
|
||
}
|
||
|
||
STATUS *get_tone_config(void)
|
||
{
|
||
return &(__this->tone);
|
||
}
|
||
|
||
u8 get_sys_default_vol(void)
|
||
{
|
||
return 21;
|
||
}
|
||
|
||
u8 get_power_on_status(void)
|
||
{
|
||
#if TCFG_IOKEY_ENABLE
|
||
struct iokey_port *power_io_list = NULL;
|
||
power_io_list = iokey_data.port;
|
||
|
||
if (iokey_data.enable) {
|
||
if (gpio_read(power_io_list->key_type.one_io.port) == power_io_list->connect_way){
|
||
return 1;
|
||
}
|
||
}
|
||
#endif
|
||
|
||
#if TCFG_ADKEY_ENABLE
|
||
if (adkey_data.enable) {
|
||
return 1;
|
||
}
|
||
#endif
|
||
|
||
#if TCFG_LP_TOUCH_KEY_ENABLE
|
||
return lp_touch_key_power_on_status();
|
||
#endif
|
||
|
||
return 0;
|
||
}
|
||
|
||
static void board_devices_init(void)
|
||
{
|
||
#if TCFG_PWMLED_ENABLE
|
||
pwm_led_init(&pwm_led_data);
|
||
#endif
|
||
|
||
#if (TCFG_IOKEY_ENABLE || TCFG_ADKEY_ENABLE || TCFG_RDEC_KEY_ENABLE || TCFG_TOUCH_KEY_ENABLE)
|
||
key_driver_init();
|
||
#endif
|
||
|
||
#if TCFG_UART_KEY_ENABLE
|
||
extern int uart_key_init(void);
|
||
uart_key_init();
|
||
#endif /* #if TCFG_UART_KEY_ENABLE */
|
||
|
||
#if TCFG_LP_TOUCH_KEY_ENABLE
|
||
lp_touch_key_init(&lp_touch_key_config);
|
||
#endif /* #if TCFG_LP_TOUCH_KEY_ENABLE */
|
||
|
||
#if (!TCFG_CHARGE_ENABLE)
|
||
CHARGE_EN(0);
|
||
CHGGO_EN(0);
|
||
#endif
|
||
|
||
#if TCFG_CHARGESTORE_ENABLE || TCFG_TEST_BOX_ENABLE || TCFG_ANC_BOX_ENABLE
|
||
chargestore_api_init(&chargestore_data);
|
||
#endif
|
||
}
|
||
|
||
//*********************************************************************************//
|
||
// linein配置 //
|
||
//*********************************************************************************//
|
||
static int linein_det_timer = 0;
|
||
|
||
static void linein_det(void)
|
||
{
|
||
u32 linein_det_voltage = 0;
|
||
|
||
linein_det_voltage = adc_get_voltage(TCFG_LINEIN_AD_CHANNEL);
|
||
|
||
printf("linein_det_voltage = %d mv\n", linein_det_voltage);
|
||
if(!get_charge_online_flag()){
|
||
if(linein_det_voltage > TCFG_LINEIN_PORT_OUT_DET_VOLTAGE && linein_det_voltage < TCFG_LINEIN_PORT_IN_DET_VOLTAGE){
|
||
printf(">>>>>>>>>>>>>>>>aux in!\n");
|
||
app_var.goto_poweroff_flag = 0;
|
||
sys_enter_soft_poweroff(NULL);
|
||
}
|
||
}
|
||
}
|
||
|
||
void linein_det_enable(void)
|
||
{
|
||
if (linein_det_timer) {
|
||
linein_det_timer = sys_timer_add(NULL, linein_det, 1000);//1000ms
|
||
}
|
||
}
|
||
void linein_det_disable(void)
|
||
{
|
||
if (linein_det_timer) {
|
||
sys_timer_del(linein_det_timer);
|
||
}
|
||
}
|
||
|
||
/* 当插入3.5MM的音频 线时，蓝牙耳机 */
|
||
/* 变成普通耳机状态,此时主控需关机，DAC设高阻 ，按键不 */
|
||
/* 支持开机和功能操作，需拔掉3.5MM线,需重新开机才恢复 */
|
||
static void linein_det_init(void)
|
||
{
|
||
adc_add_sample_ch(TCFG_LINEIN_AD_CHANNEL);
|
||
gpio_set_die(TCFG_LINEIN_CHECK_PORT, 0);
|
||
gpio_set_direction(TCFG_LINEIN_CHECK_PORT, 1);
|
||
gpio_set_pull_up(TCFG_LINEIN_CHECK_PORT, 1);
|
||
gpio_set_pull_down(TCFG_LINEIN_CHECK_PORT, 0);
|
||
|
||
linein_det_timer = sys_timer_add(NULL, linein_det, 1000);//1000ms
|
||
}
|
||
//*********************************************************************************//
|
||
// 外置芯片船运仓储模式配置 //
|
||
//*********************************************************************************//
|
||
#if TCFG_EXTERN_STORAGE_MODE_ENABLE
|
||
void external_storage_io_disable(void)
|
||
{
|
||
gpio_set_direction(TCFG_EXTERN_STORAGE_MODE_BOAT_PL_PORT,0);
|
||
gpio_set_output_value(TCFG_EXTERN_STORAGE_MODE_BOAT_PL_PORT,0);
|
||
}
|
||
#endif
|
||
|
||
extern void cfg_file_parse(u8 idx);
|
||
void board_init()
|
||
{
|
||
#if TCFG_AUDIO_HPVDD_ENABLE
|
||
//HPVDD外接1.85V电源，提升DAC输出 幅度
|
||
gpio_set_direction(TCFG_AUDIO_HPVDD_PORT,0);
|
||
gpio_set_output_value(TCFG_AUDIO_HPVDD_PORT,1);
|
||
#endif
|
||
|
||
#if TCFG_EXTERN_STORAGE_MODE_ENABLE
|
||
/* BOAT_PL正常使用时候给高，测试盒进入船运模式后，把BOAT_PLI设置为低电平，vbat彻底切断，整个系统都没电。要插充电主控才跑起来，跑起来后再次使能这个口 */
|
||
gpio_set_direction(TCFG_EXTERN_STORAGE_MODE_BOAT_PL_PORT,0);
|
||
gpio_set_output_value(TCFG_EXTERN_STORAGE_MODE_BOAT_PL_PORT,1);
|
||
#endif
|
||
board_power_init();
|
||
//adc_vbg_init();
|
||
adc_init();
|
||
cfg_file_parse(0);
|
||
devices_init();
|
||
#if TCFG_AUDIO_ANC_ENABLE
|
||
anc_init();
|
||
#endif/*TCFG_AUDIO_ANC_ENABLE*/
|
||
|
||
board_devices_init();
|
||
|
||
#if TCFG_CHARGE_ENABLE
|
||
if(get_charge_online_flag())
|
||
#else
|
||
if (0)
|
||
#endif
|
||
{
|
||
power_set_mode(PWR_LDO15);
|
||
}else{
|
||
power_set_mode(TCFG_LOWPOWER_POWER_SEL);
|
||
}
|
||
|
||
//针对硅mic要输出1给mic供电
|
||
/* gpio_set_pull_up(IO_PORTA_04, 0); */
|
||
/* gpio_set_pull_down(IO_PORTA_04, 0); */
|
||
/* gpio_set_direction(IO_PORTA_04, 0); */
|
||
/* gpio_set_output_value(IO_PORTA_04,1); */
|
||
|
||
#if TCFG_UART0_ENABLE
|
||
if (uart0_data.rx_pin < IO_MAX_NUM) {
|
||
gpio_set_die(uart0_data.rx_pin, 1);
|
||
}
|
||
#endif
|
||
|
||
#if TCFG_LINEIN_ENABLE
|
||
linein_det_init();
|
||
#endif
|
||
|
||
#if TCFG_SMART_VOICE_ENABLE
|
||
int audio_smart_voice_detect_init(struct vad_mic_platform_data *mic_data);
|
||
audio_smart_voice_detect_init((struct vad_mic_platform_data *)&vad_mic_data);
|
||
#endif /* #if TCFG_SMART_VOICE_ENABLE */
|
||
|
||
#ifdef CONFIG_BOARD_AISPEECH_VAD_ASR
|
||
extern int audio_ais_platform_asr_init(struct vad_mic_platform_data *mic_data);
|
||
audio_ais_platform_asr_init((struct vad_mic_platform_data *)&vad_mic_data);
|
||
#endif /*CONFIG_BOARD_AISPEECH_VAD_ASR*/
|
||
#ifdef AUDIO_PCM_DEBUG
|
||
extern void uartSendInit();
|
||
uartSendInit();
|
||
#endif/*AUDIO_PCM_DEBUG*/
|
||
}
|
||
|
||
/*进软关机之前默认将IO口都设置成高阻状态，需要保留原来状态的请修改该函数*/
|
||
extern void dac_power_off(void);
|
||
void board_set_soft_poweroff(void)
|
||
{
|
||
//power按键
|
||
#if TCFG_IOKEY_ENABLE
|
||
soff_gpio_protect(TCFG_IOKEY_POWER_ONE_PORT);
|
||
soff_gpio_protect(TCFG_IOKEY_MFB_ONE_PORT);
|
||
soff_gpio_protect(TCFG_IOKEY_PREV_ONE_PORT);
|
||
soff_gpio_protect(TCFG_IOKEY_NEXT_ONE_PORT);
|
||
soff_gpio_protect(TCFG_IOKEY_CALL_ONE_PORT);
|
||
#endif
|
||
|
||
#if TCFG_EXTERN_STORAGE_MODE_ENABLE
|
||
soff_gpio_protect(TCFG_EXTERN_STORAGE_MODE_BOAT_PL_PORT);
|
||
#endif
|
||
|
||
|
||
#if (!(TCFG_LP_TOUCH_KEY_ENABLE && TCFG_LP_TOUCH_KEY1_EN))
|
||
//默认唤醒io
|
||
soff_gpio_protect(IO_PORTB_01);
|
||
#endif
|
||
|
||
#if (TCFG_TEST_BOX_ENABLE || TCFG_CHARGESTORE_ENABLE || TCFG_ANC_BOX_ENABLE || TCFG_UMIDIGI_BOX_ENABLE)
|
||
power_wakeup_index_enable(2, 0);
|
||
#endif
|
||
|
||
board_set_soft_poweroff_common(NULL);
|
||
|
||
dac_power_off();
|
||
}
|
||
|
||
void sleep_exit_callback(u32 usec)
|
||
{
|
||
sleep_exit_callback_common(NULL);
|
||
|
||
putchar('>');
|
||
}
|
||
void sleep_enter_callback(u8 step)
|
||
{
|
||
/* 此函数禁止添加打印 */
|
||
if (step == 1) {
|
||
putchar('<');
|
||
} else {
|
||
|
||
sleep_enter_callback_common(NULL);
|
||
}
|
||
}
|
||
|
||
static void port_wakeup_callback(u8 index, u8 gpio)
|
||
{
|
||
log_info("%s:%d,%d",__FUNCTION__,index,gpio);
|
||
#if TCFG_UMIDIGI_BOX_ENABLE
|
||
if (index == 2) {
|
||
ldo_port_wakeup_to_cmessage();
|
||
}
|
||
#endif
|
||
switch (index) {
|
||
#if (TCFG_TEST_BOX_ENABLE || TCFG_CHARGESTORE_ENABLE || TCFG_ANC_BOX_ENABLE)
|
||
case 2:
|
||
extern void chargestore_ldo5v_fall_deal(void);
|
||
chargestore_ldo5v_fall_deal();
|
||
break;
|
||
#endif
|
||
#if TCFG_EXTERN_CHARGE_ENABLE
|
||
//外置充电下降沿触发唤醒
|
||
case 7:
|
||
if (get_charge_online_flag()) {
|
||
//检测到低电平,已经充满了
|
||
charge_event_to_user(CHARGE_EVENT_CHARGE_FULL);
|
||
}
|
||
#endif
|
||
}
|
||
}
|
||
|
||
static void aport_wakeup_callback(u8 index, u8 gpio, u8 edge)
|
||
{
|
||
log_info("%s:%d,%d",__FUNCTION__,index,gpio);
|
||
#if TCFG_CHARGE_ENABLE
|
||
switch (gpio) {
|
||
case IO_CHGFL_DET://charge port
|
||
charge_wakeup_isr();
|
||
break;
|
||
case IO_VBTCH_DET://vbat port
|
||
case IO_LDOIN_DET://ldoin port
|
||
ldoin_wakeup_isr();
|
||
break;
|
||
}
|
||
#endif
|
||
}
|
||
|
||
void board_power_init(void)
|
||
{
|
||
log_info("Power init : %s", __FILE__);
|
||
|
||
power_init(&power_param);
|
||
|
||
power_set_callback(TCFG_LOWPOWER_LOWPOWER_SEL, sleep_enter_callback, sleep_exit_callback, board_set_soft_poweroff);
|
||
|
||
#if TCFG_UMIDIGI_BOX_ENABLE
|
||
gpio_set_die(TCFG_CHARGESTORE_PORT, 1);
|
||
umidigi_chargestore_message_callback(app_umidigi_chargetore_message_deal);
|
||
#endif
|
||
|
||
power_keep_dacvdd_en(0);
|
||
|
||
power_wakeup_init(&wk_param);
|
||
|
||
/*先关闭外置充电使能，后面检测到充电插入再开启*/
|
||
#if TCFG_EXTERN_CHARGE_ENABLE
|
||
power_wakeup_disable_with_port(TCFG_EXTERN_CHARGE_PORT);
|
||
#endif
|
||
|
||
power_awakeup_set_callback(aport_wakeup_callback);
|
||
power_wakeup_set_callback(port_wakeup_callback);
|
||
|
||
|
||
}
|
||
#endif /* #ifdef CONFIG_BOARD_JL7018F_DEMO */
|