485 lines
15 KiB
C
485 lines
15 KiB
C
/* USER CODE BEGIN Header */
|
||
/**
|
||
******************************************************************************
|
||
* @file : main.c
|
||
* @brief : Main program body
|
||
******************************************************************************
|
||
* @attention
|
||
*
|
||
* Copyright (c) 2024 STMicroelectronics.
|
||
* All rights reserved.
|
||
*
|
||
* This software is licensed under terms that can be found in the LICENSE file
|
||
* in the root directory of this software component.
|
||
* If no LICENSE file comes with this, it is provided AS-IS.
|
||
*
|
||
******************************************************************************
|
||
*/
|
||
/* USER CODE END Header */
|
||
/* Includes ------------------------------------------------------------------*/
|
||
#include "main.h"
|
||
#include "spi.h"
|
||
#include "tim.h"
|
||
#include "usart.h"
|
||
#include "gpio.h"
|
||
|
||
/* Private includes ----------------------------------------------------------*/
|
||
/* USER CODE BEGIN Includes */
|
||
#include "rf433.h"
|
||
#include "rf433_config.h"
|
||
#include "rf433_hal.h"
|
||
|
||
/* 应用层模块头文件 */
|
||
#include "uart2_print.h"
|
||
#include "io_monitor.h"
|
||
#include "cmd_parser.h"
|
||
#include "relay_control.h"
|
||
|
||
/* 多通信接口统一指令处理系统模块 */
|
||
#include "multi_uart_router.h"
|
||
#include "cmd_router.h"
|
||
#include "debug_log.h"
|
||
|
||
/* W5500 Ethernet模块头文件 */
|
||
#if USE_W5500
|
||
#include "user_main.h"
|
||
#include "wiz_platform.h"
|
||
#include "wiz_interface.h"
|
||
#include "wizchip_conf.h"
|
||
#include "loopback.h"
|
||
#endif
|
||
extern void wiz_timer_handler(void);
|
||
#if (RF433_MODE == RF433_MODE_TX) || (RF433_MODE == RF433_MODE_BOTH)
|
||
#include "rf433_tx_app.h"
|
||
#endif
|
||
|
||
#if (RF433_MODE == RF433_MODE_RX) || (RF433_MODE == RF433_MODE_BOTH)
|
||
#include "rf433_rx_app.h"
|
||
#endif
|
||
|
||
/* USER CODE END Includes */
|
||
|
||
/* Private typedef -----------------------------------------------------------*/
|
||
/* USER CODE BEGIN PTD */
|
||
|
||
/* USER CODE END PTD */
|
||
|
||
/* Private define ------------------------------------------------------------*/
|
||
/* USER CODE BEGIN PD */
|
||
/* USER CODE END PD */
|
||
|
||
/* Private macro -------------------------------------------------------------*/
|
||
/* USER CODE BEGIN PM */
|
||
|
||
/* USER CODE END PM */
|
||
|
||
/* Private variables ---------------------------------------------------------*/
|
||
/* Private variables ---------------------------------------------------------*/
|
||
/* Private variables ---------------------------------------------------------*/
|
||
/* USER CODE BEGIN PV */
|
||
static uint8_t uart2_rx_byte = 0;
|
||
static uint8_t uart3_rx_byte = 0;
|
||
|
||
/* === 433 模块的接收缓存 (UART1) === */
|
||
static uint8_t u1_rx_buffer[256];
|
||
static volatile uint16_t u1_rx_len = 0;
|
||
static volatile uint32_t u1_last_rx_time = 0;
|
||
|
||
/* === 485 设备的接收缓存 (UART3) 增加这三行！=== */
|
||
static uint8_t u3_rx_buffer[512];
|
||
static volatile uint16_t u3_rx_len = 0;
|
||
static volatile uint32_t u3_last_rx_time = 0;
|
||
static volatile uint32_t u3_ignore_until = 0;
|
||
/* W5500 variables */
|
||
#if USE_W5500
|
||
#define SOCKET_ID 0
|
||
#define ETHERNET_BUF_MAX_SIZE 2048
|
||
static uint8_t ethernet_buf[ETHERNET_BUF_MAX_SIZE] = {0};
|
||
static uint16_t local_port = 8000;
|
||
#endif
|
||
/* USER CODE END PV */
|
||
/* Private function prototypes -----------------------------------------------*/
|
||
void SystemClock_Config(void);
|
||
/* USER CODE BEGIN PFP */
|
||
|
||
/* USER CODE END PFP */
|
||
|
||
/* Private user code ---------------------------------------------------------*/
|
||
/* USER CODE BEGIN 0 */
|
||
/* USER CODE END 0 */
|
||
|
||
/**
|
||
* @brief The application entry point.
|
||
* @retval int
|
||
*/
|
||
int main(void)
|
||
{
|
||
/* USER CODE BEGIN 1 */
|
||
|
||
/* USER CODE END 1 */
|
||
|
||
/* MCU Configuration--------------------------------------------------------*/
|
||
|
||
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
|
||
HAL_Init();
|
||
|
||
/* USER CODE BEGIN Init */
|
||
/* USER CODE END Init */
|
||
|
||
/* Configure the system clock */
|
||
SystemClock_Config();
|
||
|
||
/* USER CODE BEGIN SysInit */
|
||
/* USER CODE END SysInit */
|
||
|
||
/* Initialize all configured peripherals */
|
||
MX_GPIO_Init();
|
||
MX_USART1_UART_Init();
|
||
MX_SPI2_Init();
|
||
MX_USART2_UART_Init();
|
||
|
||
MX_USART3_UART_Init();
|
||
|
||
MX_TIM2_Init();
|
||
/* USER CODE BEGIN 2 */
|
||
|
||
HAL_TIM_Base_Start_IT(&htim2);
|
||
/* 初始化应用层模块 */
|
||
UART2_Print_Init();
|
||
IO_Monitor_Init();
|
||
CmdParser_Init();
|
||
Relay_Init();
|
||
|
||
/* 初始化多通信接口统一指令处理系统 */
|
||
MultiUART_Init();
|
||
CmdRouter_Init();
|
||
DebugLog_Init();
|
||
|
||
/* ============================================================== */
|
||
/* 🚀 【核心修复】将全局日志门槛提高到 INFO 级别，屏蔽所有底层 DEBUG 噪音 */
|
||
DebugLog_SetLevel(LOG_LEVEL_INFO);
|
||
/* ============================================================== */
|
||
|
||
printf("\r\n[DEBUG] 1. 启动 TIM2 中断\r\n");
|
||
HAL_TIM_Base_Start_IT(&htim2);
|
||
|
||
/* 启动UART2接收中断 */
|
||
HAL_UART_Receive_IT(&huart2, &uart2_rx_byte, 1);
|
||
|
||
/* 启动UART3接收中断 - RS485接口 */
|
||
#if USE_RS485
|
||
HAL_UART_Receive_IT(&huart3, &uart3_rx_byte, 1);
|
||
#endif
|
||
|
||
/* 初始化RF433模块 - 使用默认配置 */
|
||
rf433_init(NULL);
|
||
|
||
|
||
/* 启动UART1接收 - 使用rf433_hal中的临时变量 */
|
||
HAL_UART_Receive_IT(&huart1, &rf433_uart_rx_tmp, 1);
|
||
|
||
#if USE_W5500
|
||
printf("[DEBUG] 2. 进入 wizchip_initialize()\r\n");
|
||
wizchip_initialize();
|
||
printf("[DEBUG] 3. wizchip_initialize() 成功返回!\r\n");
|
||
|
||
printf("[DEBUG] 4. 进入 network_init()\r\n");
|
||
network_init(ethernet_buf, &default_net_info);
|
||
printf("[DEBUG] 5. network_init() 成功返回!\r\n");
|
||
printf("wizchip UDP example started\r\n");
|
||
#endif
|
||
/* ======================================= */
|
||
|
||
|
||
|
||
|
||
|
||
/* 根据配置模式初始化TX/RX应用层 */
|
||
#if (RF433_MODE == RF433_MODE_TX) || (RF433_MODE == RF433_MODE_BOTH)
|
||
/* TX模式初始化 */
|
||
rf433_tx_app_init(NULL);
|
||
rf433_tx_app_start(RF433_DEFAULT_TX_COUNT, RF433_DEFAULT_TX_INTERVAL);
|
||
#endif
|
||
|
||
#if (RF433_MODE == RF433_MODE_RX) || (RF433_MODE == RF433_MODE_BOTH)
|
||
/* RX模式初始化 */
|
||
rf433_rx_app_init(NULL);
|
||
rf433_rx_app_start();
|
||
#endif
|
||
|
||
/* 打印启动信息 */
|
||
printf("\r\n========================================\r\n");
|
||
printf("E32-433TBH-SC Application Started\r\n");
|
||
printf("System Clock: %d MHz\r\n", SystemCoreClock / 1000000);
|
||
printf("========================================\r\n");
|
||
|
||
/* USER CODE END 2 */
|
||
|
||
/* Infinite loop */
|
||
/* USER CODE BEGIN WHILE */
|
||
|
||
|
||
#if (RF433_MODE == RF433_MODE_TX) || (RF433_MODE == RF433_MODE_BOTH)
|
||
/* TX任务 */
|
||
rf433_tx_app_task();
|
||
#endif
|
||
|
||
#if (RF433_MODE == RF433_MODE_RX) || (RF433_MODE == RF433_MODE_BOTH)
|
||
/* RX任务 */
|
||
rf433_rx_app_task();
|
||
#endif
|
||
|
||
/* W5500 UDP回环任务 */
|
||
#if USE_W5500
|
||
loopback_udps(SOCKET_ID, ethernet_buf, local_port);
|
||
#endif
|
||
|
||
|
||
|
||
/* Infinite loop */
|
||
/* USER CODE BEGIN WHILE */
|
||
while (1)
|
||
{
|
||
/* === 1. 恢复系统的核心驱动引擎 === */
|
||
UART2_Print_Task();
|
||
MultiUART_Task();
|
||
IO_Monitor_Task();
|
||
|
||
/* === 2. 网络轮询任务 === */
|
||
#if USE_W5500
|
||
loopback_udps(SOCKET_ID, ethernet_buf, local_port);
|
||
#endif
|
||
|
||
/* === 3. 极速无乱码透传 === */
|
||
|
||
/* === 方案 A：从 433 收到无线数据 -> 给上位机解析 === */
|
||
if (u1_rx_len > 0 && (HAL_GetTick() - u1_last_rx_time > 20))
|
||
{
|
||
static uint8_t temp_buf1[256];
|
||
__disable_irq();
|
||
uint16_t len = u1_rx_len;
|
||
memcpy(temp_buf1, (uint8_t*)u1_rx_buffer, len);
|
||
u1_rx_len = 0;
|
||
__enable_irq();
|
||
|
||
/* 🚀 终极上位机协议：[0xAA帧头] + [设备ID] + [来源接口] + [数据长度] + [纯净数据] */
|
||
if (len >= 2 && temp_buf1[0] == 0xAA)
|
||
{
|
||
uint8_t sender_id = temp_buf1[1];
|
||
uint16_t payload_len = len - 2;
|
||
uint8_t* payload_data = &temp_buf1[2];
|
||
|
||
/* 默认 0x03 为 RS485 透传数据 */
|
||
uint8_t source_type = 0x03;
|
||
|
||
/* 判断是不是 $DI 标签 */
|
||
if (payload_len >= 3 && payload_data[0] == '$' && payload_data[1] == 'D' && payload_data[2] == 'I')
|
||
{
|
||
source_type = 0x01; /* 也是 DI 口数据，但不砍标签了，直接全发过去 */
|
||
}
|
||
/* 判断是不是网口 [NET] 标签 */
|
||
else if (payload_len >= 5 && payload_data[0] == '[' && payload_data[1] == 'N' && payload_data[2] == 'E' && payload_data[3] == 'T' && payload_data[4] == ']')
|
||
{
|
||
source_type = 0x02; /* 0x02 代表是 网络口 收到的数据 */
|
||
payload_data += 5; /* 砍掉 "[NET]" 标签 */
|
||
payload_len -= 5;
|
||
}
|
||
/* ========================================================== */
|
||
|
||
if (payload_len > 0) {
|
||
/* 重新组装终极协议帧 */
|
||
uint8_t upper_buf[260];
|
||
upper_buf[0] = 0xAA; // Byte 0: 魔法帧头
|
||
upper_buf[1] = sender_id; // Byte 1: 发送设备 ID
|
||
upper_buf[2] = source_type; // Byte 2: 数据来源 (1=DI, 2=NET, 3=485)
|
||
upper_buf[3] = (uint8_t)payload_len; // Byte 3: 真实数据长度
|
||
memcpy(&upper_buf[4], payload_data, payload_len); // Byte 4~末尾: 绝对纯净的数据
|
||
|
||
/* 发送给 485 和电脑上位机 */
|
||
MultiUART_Send(PORT_UART3, upper_buf, payload_len + 4);
|
||
MultiUART_Send(PORT_UART2, upper_buf, payload_len + 4);
|
||
}
|
||
}
|
||
else
|
||
{
|
||
/* 普通无帧头干扰数据，按原样透传 */
|
||
MultiUART_Send(PORT_UART3, temp_buf1, len);
|
||
MultiUART_Send(PORT_UART2, temp_buf1, len);
|
||
}
|
||
|
||
/* === 方案 B：从 485 收到设备数据 -> 穿上包装(附加ID) -> 通过 433 无线发射 === */
|
||
if (u3_rx_len > 0 && (HAL_GetTick() - u3_last_rx_time > 20))
|
||
{
|
||
static uint8_t temp_buf3[512];
|
||
__disable_irq();
|
||
uint16_t len = u3_rx_len;
|
||
memcpy(temp_buf3, (uint8_t*)u3_rx_buffer, len);
|
||
u3_rx_len = 0;
|
||
__enable_irq();
|
||
|
||
/* 🚀 制作“快递包”：在最前面加上 [0xAA] 和 [本机ID] */
|
||
static uint8_t rf_tx_buf[515];
|
||
rf_tx_buf[0] = 0xAA; // 贴上魔法帧头
|
||
rf_tx_buf[1] = MY_DEVICE_ID; // 贴上本机的身份证号
|
||
memcpy(&rf_tx_buf[2], temp_buf3, len); // 把 485 收到的真实数据塞进后面
|
||
|
||
/* 把带有身份证的完整包裹，通过 433 发射到空气中 */
|
||
MultiUART_Send(PORT_UART1, rf_tx_buf, len + 2);
|
||
}
|
||
|
||
/* USER CODE END WHILE */
|
||
}
|
||
}
|
||
}
|
||
/* USER CODE END 3 */
|
||
/**
|
||
* @brief System Clock Configuration
|
||
* @retval None
|
||
*/
|
||
void SystemClock_Config(void)
|
||
{
|
||
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
|
||
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
|
||
|
||
/** Initializes the RCC Oscillators according to the specified parameters
|
||
* in the RCC_OscInitTypeDef structure.
|
||
*/
|
||
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
|
||
RCC_OscInitStruct.HSEState = RCC_HSE_ON;
|
||
RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
|
||
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
|
||
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
||
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
|
||
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
|
||
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
|
||
{
|
||
Error_Handler();
|
||
}
|
||
|
||
/** Initializes the CPU, AHB and APB buses clocks
|
||
*/
|
||
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|
||
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
|
||
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
|
||
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
||
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
|
||
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
|
||
|
||
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
|
||
{
|
||
Error_Handler();
|
||
}
|
||
}
|
||
|
||
/* USER CODE BEGIN 4 */
|
||
|
||
/**
|
||
* @brief UART接收完成中断回调函数
|
||
* @note 处理UART1(RF433)、UART2(调试口)和UART3(RS485)的接收数据
|
||
* @param huart: UART句柄指针
|
||
* @retval 无
|
||
*/
|
||
/* USER CODE BEGIN 4 */
|
||
/* USER CODE BEGIN 4 */
|
||
/* USER CODE BEGIN 4 */
|
||
|
||
/* USER CODE BEGIN 4 */
|
||
|
||
/* USER CODE BEGIN 4 */
|
||
void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart)
|
||
{
|
||
if (huart->Instance == USART1) {
|
||
if (u1_rx_len < sizeof(u1_rx_buffer)) u1_rx_buffer[u1_rx_len++] = rf433_uart_rx_tmp;
|
||
u1_last_rx_time = HAL_GetTick();
|
||
HAL_UART_Receive_IT(&huart1, &rf433_uart_rx_tmp, 1);
|
||
}
|
||
else if (huart->Instance == USART3) {
|
||
/* 🚀 核心生效区：只有当单片机没有在发送数据时（度过屏蔽期），才允许接收 */
|
||
if (HAL_GetTick() >= u3_ignore_until) {
|
||
if (u3_rx_len < sizeof(u3_rx_buffer)) u3_rx_buffer[u3_rx_len++] = uart3_rx_byte;
|
||
u3_last_rx_time = HAL_GetTick();
|
||
}
|
||
HAL_UART_Receive_IT(&huart3, &uart3_rx_byte, 1);
|
||
}
|
||
else if (huart->Instance == USART2) {
|
||
HAL_UART_Receive_IT(&huart2, &uart2_rx_byte, 1);
|
||
}
|
||
}
|
||
|
||
void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart)
|
||
{
|
||
/* 彻底清除所有硬件锁死标志 */
|
||
__HAL_UART_CLEAR_OREFLAG(huart);
|
||
__HAL_UART_CLEAR_NEFLAG(huart);
|
||
__HAL_UART_CLEAR_FEFLAG(huart);
|
||
|
||
if (huart->Instance == USART1) HAL_UART_Receive_IT(&huart1, &rf433_uart_rx_tmp, 1);
|
||
else if (huart->Instance == USART3) HAL_UART_Receive_IT(&huart3, &uart3_rx_byte, 1);
|
||
else if (huart->Instance == USART2) HAL_UART_Receive_IT(&huart2, &uart2_rx_byte, 1);
|
||
}
|
||
/* USER CODE END 4 */
|
||
|
||
/* 后面原有的 HAL_UART_TxCpltCallback 保留不动... */
|
||
|
||
|
||
/**
|
||
* @brief UART发送完成中断回调函数
|
||
* @note 处理UART1/UART2/UART3发送完成，触发下一次发送
|
||
* @param huart: UART句柄指针
|
||
* @retval 无
|
||
*/
|
||
void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart)
|
||
{
|
||
if (huart->Instance == USART1)
|
||
{
|
||
/* 调用多UART路由器的UART1发送完成回调 */
|
||
MultiUART_TxCpltCallback(PORT_UART1);
|
||
}
|
||
else if (huart->Instance == USART2)
|
||
{
|
||
/* 调用UART2打印模块的发送完成回调 */
|
||
UART2_Print_TxCpltCallback();
|
||
}
|
||
else if (huart->Instance == USART3)
|
||
{
|
||
|
||
/* 调用多UART路由器的UART3发送完成回调 */
|
||
MultiUART_TxCpltCallback(PORT_UART3);
|
||
|
||
}
|
||
}
|
||
|
||
/* USER CODE END 4 */
|
||
|
||
/**
|
||
* @brief This function is executed in case of error occurrence.
|
||
* @retval None
|
||
*/
|
||
void Error_Handler(void)
|
||
{
|
||
/* USER CODE BEGIN Error_Handler_Debug */
|
||
/* User can add his own implementation to report the HAL error return state */
|
||
__disable_irq();
|
||
while (1)
|
||
{
|
||
}
|
||
/* USER CODE END Error_Handler_Debug */
|
||
}
|
||
|
||
#ifdef USE_FULL_ASSERT
|
||
/**
|
||
* @brief Reports the name of the source file and the source line number
|
||
* where the assert_param error has occurred.
|
||
* @param file: pointer to the source file name
|
||
* @param line: assert_param error line source number
|
||
* @retval None
|
||
*/
|
||
void assert_failed(uint8_t *file, uint32_t line)
|
||
{
|
||
/* USER CODE BEGIN 6 */
|
||
/* User can add his own implementation to report the file name and line number,
|
||
ex: usb_printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
|
||
/* USER CODE END 6 */
|
||
}
|
||
#endif /* USE_FULL_ASSERT */
|